소다샵 바로가기
TOP
HOME
D20S 이미지 확대 보기
  • D20S

D20S

공유
짧은설명
Dante AV 네트워크 전반에 걸쳐 유연하고 독립적인 오디오 및 Dante AV™ 비디오 라우팅을 제공합니다.
모델명
D20S
브랜드
BOLIN
D20S
0원
총 상품금액
총 할인금액
총 합계금액

상품상세정보

D20S

D20S D20S

D20S

업계 최초로 BOLIN에서 Dante AV기반 PTZ 카메라 출시
Dante AV-H™는 소프트웨어 기반 솔루션입니다.
기존 Dante 오디오 에코시스템에 원활하게 통합되도록 설계되었습니다.
유연하고 독립적인 오디오 및 Dante AV™ 비디오 라우팅을 제공합니다.
Dante AV-H™ 비디오를 Dante Studio™(Dante Video RX/TX 및 뷰어)로 전송할 수 있습니다 .
Dante 오디오 장치를 사용할 수 있도록 기존 Dante 시스템과 완벽하게 호환 가능합니다.
Encoder/Decoder Device can be configured to operate as an encoder or a decoder via firmware/software upgrade. However, the device is not able to simultaneously operate as both an encoder and decoder.
Video Codec A Optimized implementation of JPEG2000 codec in FPGA, Licensed by IntoPIX
B Dante API management interface
Video Resolutions Up to 4096x2160@60Hz; RGB 4:4:4 @ 8 bit YCbCr 4:4:4 @ 8 bit YCbCr 4:2:2 @ 8/10/12 bit
Color Depth 8-bit, 10-bit, 12-bit
Audio Formats Dante Audio over IP
Bit Rates 200 to 800 Mbps
Video Streaming Unicast or Multicast
Copy Protection HDCP 2.2 input/output, HDCP 2.3 over network
Control Protocol Visca serial control over IP, Visca-Over-IP
Latency 0.5 frame (e.g. 2160p @ 60 Hz latency is < 8 ms between encoder and decoder), Note: Overall latency may increase depending on network configurations
Bandwidth A 4kp60 10 bit 4:2:2; 500-600Mbps, results may vary depending on network configuration and management settings.
B 1080p60 10 bit 4:2:2; 150-250Mbps, results may vary depending on network configuration and management settings.
Dante Ecosystem Friendly Instant Dante Ecosystem compatibility with existing Dante-enabled products; Unified control of audio and video using Dante tools - Dante Controller
Video A Built-in HDCP encryption/decryption for video
B 800Mbps recommended maximum bit rate
c Video transport formats: Dante Video over IP
D HDR support
E HDMI monitor output loop through
HDMI IN (when using the device as an encoder) HDMI Type HDMI 2.0
Supported Resolutions 4096x2160p, 3840x2160p, 1920x1080p, 1920x1200, 1600x1200, 1280x720p, 1280x1024, 1024x768, 800x600, 720x576p, 720x480p, 640x480
Frame Rates (Hz) 23.98, 24, 25, 29.97, 30, 50, 59.94, 60
Colour Space RGB, YCbCr
Component Bit Width 8-bit, 10-bit, 12-bit
Colour Sub-Sampling 4:4:4, 4:2:2, 4:2:0
MONITOR OUT (when using the device as an encoder) HDMI Type HDMI 2.0
Supported Resolutions 4096x2160p, 3840x2160p, 1920x1080p, 1920x1200, 1600x1200, 1280x720p, 1280x1024, 1024x768, 800x600, 720x576p, 720x480p, 640x480
Frame Rates (Hz) 23.98, 24, 25, 29.97, 30, 50, 59.94, 60
Colour Space RGB, YCbCr
Component Bit Width 8-bit, 10-bit, 12-bit
Colour Sub-Sampling 4:4:4, 4:2:2,4:2:0
Embedded Audio over HDMI No
HDMI OUT (when using the device as a decoder) Supported Resolutions 4096x2160p, 3840x2160p, 1920x1080p, 1920x1200, 1600x1200, 1280x720p, 1280x1024, 1024x768, 800x600, 720x576p, 720x480p, 640x480
Frame Rates (Hz) 23.98, 24, 25, 29.97, 30, 50, 59.94, 60
Colour Space RGB, YCbCr
Component Bit Width 8-bit, 10-bit, 12-bit
Colour Sub-Sampling 4:4:4, 4:2:2, 4:2:0
SDI OUT (when using the device as a decoder) Type 12G-SDI
HDCP Protection Does not have output when the source video is HDCP content protected
Supported Resolutions 4096x2160p, 3840x2160p, 1920x1080p, 1920x1200, 1600x1200, 1280x720p, 1280x1024, 1024x768, 800x600, 720x576p, 720x480p, 640x480
Frame Rates (Hz) 23.98,24, 25, 29.97,30, 50,59.97, 60
Colour Space YCbCr
Component Bit Width 8-bit, 10-bit, 12-bit
Colour Sub-Sampling 4:2:2, 4:2:0
Standard SMPTE 292(1.5Gb/s), SMPTE 424, SMPTE 425-A(3Gb/s), SMPTE 2081, SMPTE 2082 With SMPTE352 SDI Metadata Supported
Audio Transport Formats A Up to eight channels at 44.1, 48, 88.2 or 96kHz. HDCP sourced audio channels limited to 48kHz
B Dante Audio over IP
c HDMI 7.1 embedded audio
D High-quality, low jitter with on-board clock generator for audio
Bit Depths 24, 16 and 32 bits per audio sample
Input Signal Types (when using the device as an encoder) Embedded Audio over HDMI Up to 8 channels to Dante
Sample Rate 32k to 192k, PCM24
ASRC Conversion Range 1:8 to 8:1
ASRC Latency 80 samples (1.6ms @ 48kHz)
Output Signal Types (when using the device as a decoder) Embedded Audio over HDMI 2 channels from DANTE
Sample Rate 1 48K and 96K, PCM24(24, 16 and 32 bits)
Sample Rate 2 Built-in 8-channel asynchronous sample rate converter
Ethernet General A Standard 1Gbps Ethernet
General B Auto-switching, auto-negotiating, auto discovery, full/half duplex, Dante Controller setup and control
Port 1 A IEEE 802.3ab compliant 1000BASE-T Ethernet port
Port 1 B IEEE 802.3bt Type 3 compliant, PoE++ Class 6 (60W)
Port 2 IEEE 802.3ab compliant 1000BASE-T Ethernet port
HDMI INPUT (Encoder only) HDMI 2.0 Type A connector, female; HDMI digital video/audio input
HDMI MONITOR OUTPUT (Encoder only) HDMI 2.0 Type A connector, female; HDMI digital video/audio output
HDMI OUTPUT (Decoder only) HDMI 2.0 Type A connector, female; HDMI digital video/audio output
SDI OUTPUT -
USB 1, USB 2 (Decoder only) A USB Type-A connector, female;
B USB signal extender port for connection to a mouse, keyboard
C Available Power: 100 mA at 5 VDC
USB OTG USB OTG Compliant Host computer Mouse (Dante AV transmitter)
Serial Control RS422 a RS-422 compatible with Visca control PTZ camera
RS422 b RJ45
Control Protocol VISCA
IR TX, IR RX Connector 2-pin 3.5 mm
Carrier Frequency 38 kHz
Supply Voltage 3.3V to 5V
PTZ Camera IR Receiver Front and Back
LED Indicator Powe Board Powered and Active
Codec Video Codec Active
System System Status
Error Software running status
Sync Dante Clock Slave, synchronization status
HDCP 38 kHz
HDMI HDCP 2.3, EDID
Power IEC60130-10 (JEITA standard RC-5320A) TYPE4 DC power connector; 12VDC 4A power input
Network A Powered By DanteAV Module
B Standard 1Gbps Ethernet
c Audio Flow x 15 Flows / 8 Channels per Flow (unicast or multicast)
D Video Flow x 1 Flow / 1 Channel per Flow (unicast or multicast)
E Hardware time-stamping, supporting sample-accurate playback
Power Power Consumption Power input @ 4K60: 28W
PoE PoE++, IEEE 802.3bt Type 3 class 6 compliant
Power Adaptor Input: 1.5 A maximum @ 100-240 VAC, 50/60 Hz, Output: 4A @ 12 VDC
Status 12V DC IN has priority over Ethernet 1 POE. Ethernet 1 POE will become active a fraction of a second after 12V DC IN is disconnected.
Storage Temperature -40 to 100℃
Operating Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% (non-condensing)
Heat Dissipation Cooling fan speed adjustable, 3 Level
Acoustic Noise NC35 or less, variable with cooling fan speed adjustment
Regulatory Compliance CE, FCC Part 15 Class B digital device
Dimension 216.5x148.35x44mm (LxWxH)
Weight 2.5 lbs (1.3 kg)
Chassis Metal, black finish, heat dissipation surface, fan cooled; vented rear and sides
Mounting Included HDMI cable secure mount, surface mount for TV display, base mount.
Optional 19 inch single rack mount, 19 inch dual rack mount, Din rail mount

Video Resolutions

· Up to 4096x2160@60Hz; RGB 4:4:4 @ 8 bit YCbCr 4:4:4 @ 8 bit YCbCr 4:2:2 @ 8/10/12 bit

Color Depth

· 8-bit, 10-bit, 12-bit

Video Codec

· A: Optimized implementation of JPEG2000 codec in FPGA, Licensed by IntoPIX
· B: Dante API management interface

Audio Formats

· Dante Audio over IP

Bit Rates

· 200 to 800 Mbps

Video Streaming

· Unicast or Multicast

Copy Protection

· HDCP 2.2 input/output, HDCP 2.3 over network

Control Protocol

· Visca serial control over IP, Visca-Over-IP

Latency

· 0.5 frame (e.g. 2160p @ 60 Hz latency is < 8 ms between encoder and decoder), Note: Overall latency may increase depending on network configurations

Bandwidth

· A: 4kp60 10 bit 4:2:2; 500-600Mbps, results may vary depending on network configuration and management settings.
· B: 1080p60 10 bit 4:2:2; 150-250Mbps, results may vary depending on network configuration and management settings.

Dante Ecosystem Friendly

· Instant Dante Ecosystem compatibility with existing Dante-enabled products; Unified control of audio and video using Dante tools - Dante Controller

Horizontal Angle of View

· 72.06°(W)~6.86°(T)

Vertical Angle of View

· 44.51°(W)~3.86°(T)

Min. object distance

· 80mm (Wide), 1000mm (Tele)

Min. Illumination

· Color: 0.005 lux at Auto Exposure Mode

Shutter Speed

· 1/1s~1/10000s

Focus

· Auto, Manual, One Push

Image Adjustment

· Brightness, Color(Saturation), Contrast, Sharpness, HUE

Exposure

· Auto, Custom, Manual, Indoor(50/60HZ), Gain(Auto/Manual)
· Shutter Priority, Iris Priority, Bright, Low Motion Blur

White Balance

· AUTO, OPW, Indoor, Outdoor, Locked WB, Manual
· Outdoor Auto, Sodium Vapor Lamp, Color Temperature

Control Interface

· RJ45X2-RS232/RS422, RJ45X1-IP Control, IR Remote Control

Control Protocol

· VISCA. Serial Over IP (Dante AV), VISCA Over IP

Preset Position

· 128（Speed adjustable: Up to 150°/S, 6 presets on remote controller.)

Connectors

· HDMI, USB, IP

Operating Temperature

· -10 to +40 (°C), 32 to 104 (°F)

Size

· 165x196x247mm

Weight

· 3.3kg (Net weight)

Power Input

· 12VDC, POE++ (IEEE 802.3bt)
· Min: 20W, Max: 35W

배송안내

- 배송비 : 기본배송료는 2,500원 입니다. (도서,산간,오지 일부지역은 배송비가 추가될 수 있습니다)  50,000원 이상 구매시 무료배송입니다.

- 본 상품의 평균 배송일은 0일입니다.(입금 확인 후) 설치 상품의 경우 다소 늦어질수 있습니다.[배송예정일은 주문시점(주문순서)에 따른 유동성이 발생하므로 평균 배송일과는 차이가 발생할 수 있습니다.]

- 본 상품의 배송 가능일은 0일 입니다. 배송 가능일이란 본 상품을 주문 하신 고객님들께 상품 배송이 가능한 기간을 의미합니다. (단, 연휴 및 공휴일은 기간 계산시 제외하며 현금 주문일 경우 입금일 기준 입니다.)

교환 및 반품안내

- 상품 택(tag)제거 또는 개봉으로 상품 가치 훼손 시에는 상품수령후 7일 이내라도 교환 및 반품이 불가능합니다.

- 저단가 상품, 일부 특가 상품은 고객 변심에 의한 교환, 반품은 고객께서 배송비를 부담하셔야 합니다(제품의 하자,배송오류는 제외)

- 일부 상품은 신모델 출시, 부품가격 변동 등 제조사 사정으로 가격이 변동될 수 있습니다.

- 신발의 경우, 실외에서 착화하였거나 사용흔적이 있는 경우에는 교환/반품 기간내라도 교환 및 반품이 불가능 합니다.

- 수제화 중 개별 주문제작상품(굽높이,발볼,사이즈 변경)의 경우에는 제작완료, 인수 후에는 교환/반품기간내라도 교환 및 반품이 불가능 합니다. 

- 수입,명품 제품의 경우, 제품 및 본 상품의 박스 훼손, 분실 등으로 인한 상품 가치 훼손 시 교환 및 반품이 불가능 하오니, 양해 바랍니다.

- 일부 특가 상품의 경우, 인수 후에는 제품 하자나 오배송의 경우를 제외한 고객님의 단순변심에 의한 교환, 반품이 불가능할 수 있사오니, 각 상품의 상품상세정보를 꼭 참조하십시오. 

환불안내

- 상품 청약철회 가능기간은 상품 수령일로 부터 7일 이내 입니다.

AS안내

- 소비자분쟁해결 기준(공정거래위원회 고시)에 따라 피해를 보상받을 수 있습니다.

- A/S는 판매자에게 문의하시기 바랍니다.

이미지 확대보기D20S

D20S
  • D20S
닫기

비밀번호 인증

글 작성시 설정한 비밀번호를 입력해 주세요.

닫기

장바구니 담기

상품이 장바구니에 담겼습니다.
바로 확인하시겠습니까?

찜 리스트 담기

상품이 찜 리스트에 담겼습니다.
바로 확인하시겠습니까?